Theoretical analysis and test verification of pull-out forces in shear connectors of composite beam under negative bending moment

Abstract

A mechanical model of steel-concrete composite beams considering horizontal slip and vertical pull-out effects under negative bending moment was established based on the theory of elastic deformation. By using the principle of force equilibrium and deformation compatibility condition, the differential equation was derived and deduced using computational calculation program, in which the formula of the pull-out force in shear connectors under negative bending moment was obtained. The experiment was conducted in order to verify the reliability of theoretical results. The results show: under the same load condition, the pull-out force of a single stud increases with the increase of the stud spacing. All the theoretical results were verified by comparing with experiment results to illustrate the accuracy and reliability of the calculation method. It provides a theoretical reference for the study of the interface interaction considering horizontal slip and vertical pull-out effect in the negative bending moment region of continuous composite beams.     

加氢反应器头盖密封质量控制探讨

加氢反应器是加氢装置的重要组成部分,反应器头盖因工况复杂,导致密封难度较大,密封不严,会导致整个装置不能正常运转。为此,就其头盖拆装及密封问题进行探讨,提出有效的质量控制措施。     

飞秒激光光斑轮廓的傅里叶描述子重建及特征提取

在利用飞秒激光对单晶硅材料进行微尺度烧蚀时,衍生的等离子体发光光斑中蕴含着大量的加工信息。如何有效提取光斑图像的几何特征信息,对研究飞秒激光烧蚀加工工艺过程具有重要意义。轮廓特征是描述激光光斑最重要的特征之一,本文着重分析了等离子体光斑轮廓特征与光斑运动规律间的关系及光斑运动情况分类方法。首先,考虑到光斑微弱的特性,对光斑图像进行增强处理。其次,采用链码方法提取光斑轮廓特征,并利用傅里叶描述子低频特性,选取少量的描述子重建光斑图像轮廓特征,减少了复杂的计算量,有效提高了光斑图像分类的速度与质量。最后,运用Hu不变矩特征证明傅里叶描述子用于提取激光光斑对轮廓特征的有效性。     

Effects of Sparger Holes on Gas-Liquid Hydrodynamics in Bubble Columns

A multiphase second-order moment turbulent model was developed including an improved closure Reynolds stress transport to describe effectively the anisotropic characteristics of bubble-liquid turbulent flow. The two-phase hydrodynamics in a bubble column were numerically simulated by an in-house code. The effect of the amount of jetting holes on bubble-liquid hydrodynamics in relationship with a cell culture was investigated. Firstly, the bubble energy production correlation was proposed to verify the higher cell damage rate near gas inlet regions. The larger amounts of jetting holes resulted in an increase of bubble stress, bubble kinetic energy, and energy dissipation, particularly bubble energy production at the near gas inlet, which boosted cell damage.     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

考虑关节角加速度约束的仿人机器人偏摆力矩控制方法

针对仿人机器人步行过程中存在的机器人关节角加速度约束影响控制性能的问题，提出一种考虑关节角加速度约束的仿人机器人偏摆力矩控制方法.该方法充分考虑了双臂在摆动过程中对偏摆力矩的影响，根据力矩平衡条件得到需要抵消的偏摆力矩的大小与方向，将偏摆力矩的控制问题转化为带约束条件的二次规划问题，并设计了一种在线变步长迭代算法计算得到优化后的双臂摆动轨迹.实验表明，该方法能有效抵消机器人步行中产生的偏摆力矩，避免控制过程中的"削峰"现象，有效提高机器人的步行稳定性.     

基于区域特征和质心关系的两步法阀板检测

针对冲压阀板中毛刺、冲压孔堵塞等缺陷的检测问题,提出了一种基于面积特征的通孔数目检测和基于质心关系的快速模板匹配检测的两步视觉检测方案。首先采用通孔数检测初步判定零件是否存在冲压孔堵塞缺陷,之后采用模板匹配精确检测边缘毛刺缺陷。利用区域面积特征实现通孔数检测;提出了一种限定条件的最小二乘法圆拟合方法和一种基于圆心特征的快速模板匹配方法,实现边缘毛刺等缺陷的精确检测。实验结果表明,这种两步检测方案检测速度快精准度高,能够满足阀板生产线的检测要求。     

Design and locomotion analysis of two kinds of rolling expandable mobile linkages with a single degree of freedom

Frontiers of Mechanical Engineering - This study presents two kinds of rolling robots that are able to roll by deforming their outer shapes with a single degree of freedom. Each robot is an...